Garage Door Repair
Garage Door Repair. Mesa Garage Doors can repair most makes of garage doors. We have over 50 service trucks staffed with factory trained experts to assist you.
Contact our service department at 1-800-951-7700 to schedule an appointment.
We may be able to service you the same day!
We should be able to schedule the appointment same day if reported early.
Garage Door Repair
Garage door repair can be a tricky and dangerous operation if you don't know what you are doing. There are extremely powerful springs that counter balance the weight of the garage door. The springs are connected through a torsion bar to cables. If the cables become loose it can be very dangerous. Most garage door repair should be performed by an expert.Garage Door Opener Repair
Garage Door Spring Repair
Never attempt garage door spring repair unless you are a good engineer. This is tricky, dangerous and requires special equipment. If you aren't convinced and want to do it yourself here is a link Garage Door Spring Repair. A spring breaking is loud. If you hear a loud bang when opening or closing the door, its probably a broken spring. If the opener is straining to open the door, it may be a broken spring. If the door cocks to one side when you try to open it, it may be a broken spring.Even if you garage door opens don't use the opener, as it may burn it out.
Garage Door Cable Repair
Don't do it your self. This is dangerous and requires special equipment. The symptoms are similar to a broken spring without the loud bang.
Garage Door Off Track
The Garage doors we install don't just hop off their track. If you hit the door with your car, bashed it in some way or a high wind did it, the door should be inspected by a professional. There may be something bent or broken.
Trouble shooting Garage Doors, Please check list before calling so that you do not incur a service call fee.
I push the button to close my garage door. The Garage door only goes down part of the way then stops and goes back up and the light starts blinking.
Ok Mr. Smith, it is probably the opener safety sensors. The best way to check the sensors is to keep pushing the wall button and see if the doors will go down. If it continues until you remove your finger the sensors are out of alignment.
Inspect the photo eyes sensor. The sensor is the small black boxes the near the bottom of your garage door frame which is usually installed on the tracks with a small bracket.
1. Make sure that there is not something blocking the sensors from communicating with each other. Bicycle etc.
2. You can look at where the sensors are pointed. They need to be pointed at each other. If they are not just try to push the out of alignment sensor into alignment.
My Garage Door Motor runs but the door does not close.
This is an indication that the belt may be broken, your chain is off, your gearbox may be broken or the opener has been disengaged.
1. Look at the opener when it is operating. Is the belt, chain or screw moving?
a. YES (if not please skip to "b" below)
i. Can you move the door by pushing it up or down.
1. YES.
a. Your door is not engaged. Please try to engage it. If this does not work the problem need to be addressed by one of our trained technicians.
b. NO
i. We need to send one of our trained technicians.
My Garage Door Remote is not working
1. Please replace the battery.
2. If the battery has been replaced the repair requires one of our trained service technicians.
To erase all Liftmaster codes.
1. Push and hold the learn code button for 15 seconds. At that point all the existing codes are deleted
To reprogram your remote.
1. Press the learn code button on your motor head.
2. Within 15 seconds press the remote button 3 times. The remote is programmed.
The Garage Door Opener light does not come on when I open the door.
1. Please make sure you have replaced the bulb.
2. If you have replaced the bulb then we need to send one of our trained technicians.
The garage door opener light does not go off after a period of time.
1. Passing the sensor beam will trigger the opener light. Make sure you are not triggering the light by passing the sensor light.
2. Some wall buttons have a light switch. Please make sure that your wall button does not have the light switch on.
Garage Door Remote not working from short range
• Check your batteries to make sure that they are working. Change batteries if need be.
• Make sure that your remote control is not too close to the roof of car.
• If there was a power outage, re-program your remote.
To erase all existing Liftmaster remote codes:
• Push the "Smart Button" (square, green) on the back of your opener and hold it for about 15 seconds.
• The light will flash and you can let go.
Reprogramming your Liftmaster garage door opener remote: (For other remote programming feel free to call us for instructions)
• Push button on your remote clicker.
• Push "Smart Learn Button" (square, green) on the back of your operator.
• Opener light does not come on when door opens
• Burned out bulb or bad light socket on the opener.
Garage door opener light does not go off after the delay period of time.
• Is the main light switch on the wall mount is on?• Check photo eye sensor, is the photo eye beam being tripped by someone or something passing in front of it?
Our office hours are:
Monday to Friday 8:00 AM to 6:00 PM,
Sat-Sun 8:00 AM to :500 PM
